Semiconductors and Electronics MCQ questions with answers
IOE Entrance Exam · Physics. Below are 10 sample questions from this chapter, each with the correct answer and an explanation. The full set of 644 questions is free to practise on Prashnalaya.
Topics covered: Energy bands in solids: conductors, semiconductors and insulators, Intrinsic and extrinsic semiconductors (n-type and p-type), Logic gates: AND, OR, NOT, NAND, NOR – truth tables and symbols, P-N junction: formation and depletion region, Rectification: half-wave and full-wave, Transistor: types (npn, pnp), configurations and amplification, Zener diode: breakdown and voltage regulation
- Q1.A Zener diode is normally operated in reverse bias for voltage regulation.
Show answer and explanation
This is true because a Zener diode is specially designed to work safely in the reverse breakdown region, where it maintains an almost constant voltage across itself and is therefore used for voltage regulation. - Q2.In the reverse breakdown region of a Zener diode, a small change in current can produce only a very small change in voltage across it.
Show answer and explanation
This is true because the reverse characteristic of a Zener diode in breakdown is very steep. That means the voltage remains nearly constant even when the current changes over a range, which is the basis of regulation. - Q3.A Zener diode is used as a rectifier in forward bias in most voltage regulator circuits.
Show answer and explanation
This is false because in voltage regulator circuits the Zener diode is not primarily used as a rectifier. It is connected in reverse bias and operated in the breakdown region to keep the output voltage nearly constant. - Q4.The breakdown voltage of a Zener diode is also called the Zener voltage.
Show answer and explanation
This is true because the reverse voltage at which the diode starts conducting heavily without large change in voltage is called the breakdown voltage or Zener voltage, usually written as . - Q5.If the input voltage of a simple Zener regulator increases, the load voltage always increases by the same amount.
Show answer and explanation
This is false because in a properly working Zener regulator, the Zener diode absorbs the effect of input variation by changing its current. As a result, the load voltage remains nearly constant instead of increasing by the same amount. - Q6.In a shunt voltage regulator using a Zener diode, the Zener diode is connected in parallel with the load.
Show answer and explanation
This is true because a basic Zener regulator is a shunt regulator. The diode is placed across the load so that the voltage across the load stays approximately equal to the Zener voltage. - Q7.A series resistor is commonly used with a Zener diode to limit the current through the diode.
Show answer and explanation
This is true because if a resistor were not used, excessive current could flow through the Zener diode in breakdown and damage it. The series resistor drops excess voltage and restricts current to a safe value. - Q8.When the load current increases in a Zener regulator, the Zener current usually increases if the input voltage remains constant.
Show answer and explanation
This is false because with constant input voltage, the current through the series resistor is approximately fixed. If the load current increases, a larger portion of that current goes to the load, so the Zener current usually decreases. - Q9.For proper voltage regulation, the Zener diode must remain in its breakdown region during operation.
Show answer and explanation
This is true because the nearly constant-voltage behavior of the Zener diode appears only in the reverse breakdown region. If the operating point leaves this region, the regulation effect is lost. - Q10.A Zener diode with nominal voltage can ideally maintain about across the load in a suitable regulator circuit.
Show answer and explanation
This is true because in a simple Zener regulator, the load is connected in parallel with the Zener diode, so the load voltage is approximately equal to the Zener voltage, here about .
Practise all 644 Semiconductors and Electronics questions
Instant feedback, explanations, timed mock tests and progress tracking. Free on the web and Android.
More Physics chapters
- Circular Motion and Gravitation MCQs969
- DC Circuits MCQs792
- Dispersion of Light MCQs547
- Elasticity MCQs550
- Electromagnetic Induction and AC MCQs840
- Electrostatics MCQs888
- Fluid Mechanics MCQs868
- Heat and Thermodynamics MCQs1,534
- Kinematics MCQs426
- Magnetic Effects of Current MCQs651
- Magnetic Properties of Matter MCQs382
- Modern Physics MCQs930
- Newton's Laws and Friction MCQs744
- Radioactivity and Nuclear Physics MCQs693
- Recent Trends in Physics MCQs771
- Reflection and Refraction MCQs932
- Rotational Dynamics MCQs581
- Simple Harmonic Motion MCQs644
- Thermoelectric Effect MCQs353
- Units, Dimensions and Vectors MCQs533
- Wave Optics MCQs680
- Waves and Sound MCQs925
- Work, Energy and Power MCQs770
