Thermoelectric Effect MCQ questions with answers
IOE Entrance Exam · Physics. Below are 10 sample questions from this chapter, each with the correct answer and an explanation. The full set of 353 questions is free to practise on Prashnalaya.
Topics covered: Peltier effect: definition and applications, Seebeck effect: thermoelectric emf and thermocouple, Thermopile: construction and uses, Thomson effect: definition and significance
- Q1.What is the Peltier effect?
- A.Production of heat in a conductor due to resistance
- B.Absorption or evolution of heat at a junction when electric current passes
- C.Production of emf due to temperature difference between junctions
- D.Transfer of heat through a metal by conduction only
Show answer and explanation
Answer: B. Absorption or evolution of heat at a junction when electric current passes
The Peltier effect is the phenomenon in which heat is absorbed at one junction and released at the other junction of two dissimilar conductors when an electric current passes through the circuit. It is different from Joule heating, which occurs due to resistance throughout the conductor. - Q2.The Peltier effect is observed at the junction of
- A.two dissimilar conductors
- B.two similar conductors
- C.a conductor and an insulator
- D.two semiconductors only of same type
Show answer and explanation
Answer: A. two dissimilar conductors
The Peltier effect requires a junction of two dissimilar materials. In thermoelectric circuits, this is usually two different conductors or semiconductors. Similar conductors do not produce the required thermoelectric junction behavior. - Q3.When the direction of current in a thermoelectric junction is reversed, the Peltier effect at that junction
- A.remains unchanged
- B.disappears permanently
- C.changes from heating to cooling or vice versa
- D.becomes equal to Joule heating
Show answer and explanation
Answer: C. changes from heating to cooling or vice versa
A key feature of the Peltier effect is reversibility. If the current direction is reversed, the junction that was absorbing heat starts releasing heat, and the junction that was releasing heat starts absorbing heat. - Q4.The SI unit of Peltier coefficient is
- A.volt per kelvin
- B.joule per coulomb
- C.watt per meter
- D.ohm per kelvin
Show answer and explanation
Answer: B. joule per coulomb
The Peltier coefficient is defined as the heat absorbed or evolved per unit charge crossing the junction. Therefore its unit is joule per coulomb, which is also dimensionally equivalent to volt. - Q5.Which statement best distinguishes the Peltier effect from Joule heating?
- A.Peltier effect occurs only in vacuum
- B.Peltier effect is irreversible while Joule heating is reversible
- C.Peltier effect occurs at junctions and depends on current direction
- D.Peltier effect is proportional to square of current only
Show answer and explanation
Answer: C. Peltier effect occurs at junctions and depends on current direction
Peltier heating or cooling occurs specifically at a junction of dissimilar materials and reverses when the current direction is changed. Joule heating occurs throughout a resistor and always produces heat irrespective of current direction. - Q6.A practical application of the Peltier effect is found in
- A.step-up transformer
- B.thermoelectric cooler
- C.electrostatic precipitator
- D.induction motor
Show answer and explanation
Answer: B. thermoelectric cooler
Thermoelectric coolers use the Peltier effect. When current is passed through the thermoelectric module, one side becomes cold and the other side becomes hot. - Q7.At the cold junction of a Peltier device, heat is
- A.always generated due to resistance
- B.neither absorbed nor released
- C.absorbed from the surroundings
- D.converted directly into magnetic energy
Show answer and explanation
Answer: C. absorbed from the surroundings
In cooling mode, the cold junction absorbs heat from the nearby region. This is the basis of refrigeration using the Peltier effect. - Q8.The Peltier coefficient mainly depends on
- A.the color of the wire
- B.the nature of the pair of materials and temperature
- C.the length of the connecting wire only
- D.the cross-sectional area only
Show answer and explanation
Answer: B. the nature of the pair of materials and temperature
The Peltier coefficient depends on the thermoelectric properties of the two materials forming the junction and also varies with temperature. It is not determined solely by length or area. - Q9.If is the Peltier heat produced or absorbed when charge passes through a junction, then the Peltier coefficient is
- A.
- B.
- C.
- D.
Show answer and explanation
Answer: A.
By definition, the Peltier coefficient is the heat absorbed or evolved per unit charge crossing the junction. Hence . - Q10.Which one of the following is not a thermoelectric effect?
- A.Seebeck effect
- B.Peltier effect
- C.Thomson effect
- D.Hall effect
Show answer and explanation
Answer: D. Hall effect
Seebeck, Peltier, and Thomson effects are thermoelectric effects. The Hall effect is related to the deflection of charge carriers in a magnetic field and is different.
Practise all 353 Thermoelectric Effect questions
Instant feedback, explanations, timed mock tests and progress tracking. Free on the web and Android.
More Physics chapters
- Circular Motion and Gravitation MCQs969
- DC Circuits MCQs792
- Dispersion of Light MCQs547
- Elasticity MCQs550
- Electromagnetic Induction and AC MCQs840
- Electrostatics MCQs888
- Fluid Mechanics MCQs868
- Heat and Thermodynamics MCQs1,534
- Kinematics MCQs426
- Magnetic Effects of Current MCQs651
- Magnetic Properties of Matter MCQs382
- Modern Physics MCQs930
- Newton's Laws and Friction MCQs744
- Radioactivity and Nuclear Physics MCQs693
- Recent Trends in Physics MCQs771
- Reflection and Refraction MCQs932
- Rotational Dynamics MCQs581
- Semiconductors and Electronics MCQs644
- Simple Harmonic Motion MCQs644
- Units, Dimensions and Vectors MCQs533
- Wave Optics MCQs680
- Waves and Sound MCQs925
- Work, Energy and Power MCQs770
