Physical Chemistry – Volumetric Analysis MCQ questions with answers
CEE Entrance · Chemistry. Below are 10 sample questions from this chapter, each with the correct answer and an explanation. The full set of 273 questions is free to practise on Prashnalaya.
Topics covered: Equivalent weights and expression of concentration (%, g/L, normality, molarity, molality, formality, ppm, ppb, mole fraction), Law of equivalence and normality equation, Primary and secondary standard substances
- Q1.Arrange the following steps in the correct order for solving a volumetric analysis problem using the normality equation.
Identify the n-factor of each reacting substance
Apply
Convert given concentration into normality if needed
Substitute the known values and calculate the unknown- A.Substitute the known values and calculate the unknown
- B.Apply
- C.Convert given concentration into normality if needed
- D.Identify the n-factor of each reacting substance
Show answer and explanation
Answer: A. Substitute the known values and calculate the unknown, B. Apply , C. Convert given concentration into normality if needed, D. Identify the n-factor of each reacting substance
To solve a volumetric analysis problem using the normality equation, the steps must follow the logical order of preparing the required quantities first and then applying the formula.
1. **Identify the n-factor of each reacting substance**
Normality depends on the equivalent concept, and equivalent weight is determined by the -factor. Without knowing the -factor, normality cannot be correctly found from molarity or mass concentration.
2. **Convert given concentration into normality if needed**
If concentration is given in molarity, strength, or some other form, it must be converted into normality before using the normality relation. The relation is:
So this step comes after identifying the -factor.
3. **Apply **
In volumetric analysis, at the equivalence point, the gram-equivalents of the two reacting substances are equal. Therefore,
This is the main equation used after the normalities are known.
4. **Substitute the known values and calculate the unknown**
Once the correct equation is set up, insert the known values and solve for the required quantity.
So the correct order is:
1. Identify the n-factor of each reacting substance
2. Convert given concentration into normality if needed
3. Apply
4. Substitute the known values and calculate the unknown - Q2.Arrange the following substances in the correct order from most suitable primary standard to least suitable primary standard based on stability, purity, and resistance to moisture absorption: potassium hydrogen phthalate, sodium carbonate, oxalic acid dihydrate, sodium hydroxide.
- A.sodium hydroxide
- B.potassium hydrogen phthalate
- C.oxalic acid dihydrate
- D.sodium carbonate
Show answer and explanation
Answer: A. sodium hydroxide, B. potassium hydrogen phthalate, C. oxalic acid dihydrate, D. sodium carbonate
Potassium hydrogen phthalate is an excellent primary standard because it is highly pure, stable, non-hygroscopic, and has high molar mass. Sodium carbonate is also a good primary standard when properly dried. Oxalic acid dihydrate can be used as a primary standard but is less preferred than the first two due to handling limitations. Sodium hydroxide is not a primary standard because it absorbs moisture and carbon dioxide from air. Therefore, the correct order is potassium hydrogen phthalate → sodium carbonate → oxalic acid dihydrate → sodium hydroxide. - Q3.Arrange the steps in the correct sequence for preparing and standardizing a secondary standard to use an approximately 0.1 M sodium hydroxide solution using oxalic acid as a primary standard: prepare approximate NaOH solution, prepare standard oxalic acid solution, fill burette with NaOH, titrate against oxalic acid to find exact concentration.
- A.prepare standard oxalic acid solution
- B.fill burette with NaOH
- C.prepare approximate NaOH solution
- D.titrate against oxalic acid to find exact concentration
Show answer and explanation
Answer: A. prepare standard oxalic acid solution, B. fill burette with NaOH, C. prepare approximate NaOH solution, D. titrate against oxalic acid to find exact concentration
A secondary standard such as sodium hydroxide cannot be prepared accurately by weighing alone because it is hygroscopic and absorbs carbon dioxide. First, an approximate NaOH solution is prepared. Then a standard oxalic acid solution is prepared because oxalic acid is a primary standard. The NaOH solution is placed in the burette, and finally titration is carried out against the known oxalic acid solution to determine the exact concentration of NaOH. Hence the correct sequence is prepare approximate NaOH solution → prepare standard oxalic acid solution → fill burette with NaOH → titrate against oxalic acid to find exact concentration. - Q4.Arrange the following substances in increasing order of suitability for direct preparation of a standard solution by weighing: hydrochloric acid, sodium hydroxide, potassium permanganate, sodium carbonate.
- A.potassium permanganate
- B.sodium hydroxide
- C.sodium carbonate
- D.hydrochloric acid
Show answer and explanation
Answer: A. potassium permanganate, B. sodium hydroxide, C. sodium carbonate, D. hydrochloric acid
Hydrochloric acid is least suitable for direct preparation as a standard because concentrated HCl is volatile, so exact concentration cannot be obtained by simple dilution. Sodium hydroxide is also unsuitable because it absorbs moisture and carbon dioxide. Potassium permanganate is better than these two but is still not a primary standard because it often contains impurities and decomposes slowly; it must be standardized before use. Sodium carbonate is highly suitable because it is pure, stable, and can be weighed accurately. Thus the increasing order is hydrochloric acid → sodium hydroxide → potassium permanganate → sodium carbonate. - Q5.Arrange the following indicators or observations in the proper order of use during standardization of with oxalic acid: pipette oxalic acid into flask, add phenolphthalein, run NaOH from burette, observe permanent faint pink end point.
- A.observe permanent faint pink end point
- B.run NaOH from burette
- C.pipette oxalic acid into flask
- D.add phenolphthalein
Show answer and explanation
Answer: A. observe permanent faint pink end point, B. run NaOH from burette, C. pipette oxalic acid into flask, D. add phenolphthalein
During the titration, the standard oxalic acid solution is first transferred accurately into the conical flask using a pipette. Then phenolphthalein is added because it is suitable for strong base versus weak acid type end point behavior in this practical setup. Next, NaOH from the burette is added slowly. The end point is the first permanent faint pink color. Therefore, the correct order is pipette oxalic acid into flask → add phenolphthalein → run NaOH from burette → observe permanent faint pink end point. - Q6.Arrange the following substances in the correct order from most likely to require standardization before use to least likely to require standardization before use in volumetric analysis: , , , potassium hydrogen phthalate.
- A.
- B.potassium hydrogen phthalate
- C.
- D.
Show answer and explanation
Answer: A. , B. potassium hydrogen phthalate, C. , D.
Potassium permanganate most clearly requires standardization because it is not sufficiently pure and its solution changes on standing. Hydrochloric acid also requires standardization because it is volatile and cannot usually be prepared to exact concentration by direct dilution alone. Sodium hydroxide requires standardization as well because it absorbs moisture and carbon dioxide from air, but in comparison HCl volatility is often considered a stronger reason in solution preparation. Potassium hydrogen phthalate is a classic primary standard and does not require prior standardization. Hence the best order is → → → potassium hydrogen phthalate. - Q7.Arrange the following concentration units in increasing order of magnitude for aqueous dilute solutions, from the smallest amount of solute to the largest amount of solute: ppb, ppm, %, g/L.
- A.g/L
- B.%
- C.ppm
- D.ppb
Show answer and explanation
Answer: A. g/L, B. %, C. ppm, D. ppb
For dilute aqueous solutions, ppb means parts per billion, which is smaller than ppm or parts per million. Percentage represents parts per hundred, so it is much larger than ppm. The unit g/L is usually larger than ppm for ordinary solution comparisons because 1 ppm in water is about 1 mg/L, while 1 g/L = 1000 mg/L. Therefore the increasing order is ppb, ppm, g/L, %. - Q8.Arrange the following concentration terms in the order in which the denominator changes from mass of solution to amount of solvent to volume of solution to total moles of mixture: mass percent, molality, molarity, mole fraction.
- A.mole fraction
- B.mass percent
- C.molarity
- D.molality
Show answer and explanation
Answer: A. mole fraction, B. mass percent, C. molarity, D. molality
Mass percent is based on mass of solute divided by mass of solution. Molality is moles of solute per kilogram of solvent. Molarity is moles of solute per litre of solution. Mole fraction is moles of one component divided by total moles of all components in the mixture. Hence the required order is mass percent, molality, molarity, mole fraction. - Q9.For the acid-base reactions shown, arrange the acids in increasing order of equivalent weight when reacting completely with a strong base:
a strong monoprotic acid represented by and basicity 1
a diprotic acid represented by and basicity 2
a triprotic acid represented by and basicity 3
Use the labels c, b, a for ordering if appropriate.- A.a strong monoprotic acid represented by and basicity 1
- B.a triprotic acid represented by and basicity 3
- C.a diprotic acid represented by and basicity 2
Show answer and explanation
Answer: A. a strong monoprotic acid represented by and basicity 1, B. a triprotic acid represented by and basicity 3, C. a diprotic acid represented by and basicity 2
For an acid reacting completely with a strong base, the equivalent weight is given by
Here, each acid has molar mass .
Now calculate for each one:
1. Monoprotic acid, basicity :
2. Diprotic acid, basicity :
3. Triprotic acid, basicity :
So the equivalent weights are:
- triprotic acid:
- diprotic acid:
- monoprotic acid:
In increasing order (smallest to largest):
Therefore, the correct order is:
triprotic acid diprotic acid monoprotic acid. - Q10.A solution is prepared by dissolving 1 mol of solute in 1 kg of water. Arrange the following concentration expressions in increasing order of their numerical values for this solution: mole fraction of solute, molality, molarity, ppm. Assume density is close to 1 g/mL for rough comparison.
- A.ppm
- B.molarity
- C.mole fraction of solute
- D.molality
Show answer and explanation
Answer: A. ppm, B. molarity, C. mole fraction of solute, D. molality
For 1 mol solute in 1 kg water, moles of water are about mol. So mole fraction of solute = , the smallest numerical value here. Molality = mol/kg = . If density is close to g/mL, total volume is slightly more than L, so molarity is slightly less than , thus molarity < molality. ppm is a very large numerical value compared to these because mol of many solutes corresponds to tens of grams in about kg solution, giving ppm in the order of to or more. Therefore the increasing order is mole fraction, molarity, molality, ppm.
Practise all 273 Physical Chemistry – Volumetric Analysis questions
Instant feedback, explanations, timed mock tests and progress tracking. Free on the web and Android.
More Chemistry chapters
- Analytical Chemistry MCQs1,034
- Applied Chemistry MCQs1,192
- Inorganic Chemistry – Bio-inorganic MCQs378
- Inorganic Chemistry – Metals MCQs1,044
- Inorganic Chemistry – Non-metals MCQs775
- Organic Chemistry – Alcohols & Phenols MCQs438
- Organic Chemistry – Aldehydes & Ketones MCQs208
- Organic Chemistry – Aromatic MCQs291
- Organic Chemistry – Carboxylic Acids & Derivatives MCQs701
- Organic Chemistry – Ethers MCQs276
- Organic Chemistry – General MCQs697
- Organic Chemistry – Haloalkanes & Haloarenes MCQs371
- Organic Chemistry – Hydrocarbons MCQs407
- Organic Chemistry – Nitro Compounds & Amines MCQs475
- Organic Chemistry – Organometallic MCQs324
- Physical Chemistry – Atomic Structure MCQs571
- Physical Chemistry – Basic Concepts MCQs165
- Physical Chemistry – Chemical Bonding MCQs659
- Physical Chemistry – Chemical Equilibrium MCQs377
- Physical Chemistry – Chemical Kinetics MCQs581
- Physical Chemistry – Electrochemistry MCQs549
- Physical Chemistry – Ionic Equilibrium MCQs519
- Physical Chemistry – Nuclear Chemistry MCQs255
- Physical Chemistry – Periodic Table MCQs596
- Physical Chemistry – Redox Reactions MCQs382
- Physical Chemistry – States of Matter (Gas) MCQs413
- Physical Chemistry – States of Matter (Liquid) MCQs306
- Physical Chemistry – States of Matter (Solid) MCQs269
- Physical Chemistry – Stoichiometry MCQs294
- Physical Chemistry – Thermodynamics MCQs752
