Mechanics – Elasticity MCQ questions with answers

CEE Entrance · Physics. Below are 10 sample questions from this chapter, each with the correct answer and an explanation. The full set of 279 questions is free to practise on Prashnalaya.

Topics covered: Moduli of elasticity: Young's modulus, bulk modulus, modulus of rigidity, Poisson's ratio and elastic potential energy density, Stress and strain: types and definitions

  1. Q1.
    Arrange the following elastic constants in increasing order for a typical isotropic solid material: modulus of rigidity , Young's modulus , and bulk modulus .
    • A.bulk modulus
    • B.Young's modulus
    • C.modulus of rigidity
    Show answer and explanation

    Answer: A. bulk modulus , B. Young's modulus , C. modulus of rigidity

    For an isotropic solid, the elastic constants are related by and , where Poisson's ratio usually lies between 0 and 0.5. Hence is generally smaller than , and is generally greater than . Therefore the increasing order is .
  2. Q2.
    A wire of original length is stretched by a gradually increasing force. Arrange the following physical quantities in the correct sequence as they are used to determine Young's modulus experimentally. stress, strain, extension, applied force.
    • A.strain
    • B.applied force
    • C.stress
    • D.extension
    Show answer and explanation

    Answer: A. strain, B. applied force, C. stress, D. extension

    To determine Young's modulus experimentally for a stretched wire, we follow the physical and calculation sequence from cause to measured effect and then to derived quantities.

    Young's modulus is defined as

    where

    and


    Now the correct sequence is:

    1. applied force — A gradually increasing force is first applied to the wire.
    2. extension — Because of this force, the wire elongates, and the extension is measured.
    3. stress — Using the applied force and the wire's cross-sectional area, stress is calculated.
    4. strain — Using the measured extension and original length, strain is calculated.

    After obtaining stress and strain, Young's modulus is found from their ratio.

    So the correct order is:


    Hence the given marked answer is correct.
  3. Q3.
    Arrange the following materials in decreasing order of resistance to change in volume when equal pressure is applied: steel, rubber, water, and air.
    • A.water
    • B.air
    • C.steel
    • D.rubber
    Show answer and explanation

    Answer: A. water, B. air, C. steel, D. rubber

    Resistance to volume change depends on bulk modulus. Larger bulk modulus means less compressibility. Solids like steel have very high bulk modulus, liquids like water have lower but still large bulk modulus, rubber is more compressible than water, and air is highly compressible with very small bulk modulus. Therefore the decreasing order of resistance is steel, water, rubber, air.
  4. Q4.
    Arrange the following quantities in the correct order to obtain the modulus of rigidity of a cylindrical wire by torsion method. angle of twist, torque applied, radius and length of wire, modulus of rigidity calculation.
    • A.radius and length of wire
    • B.modulus of rigidity calculation
    • C.torque applied
    • D.angle of twist
    Show answer and explanation

    Answer: A. radius and length of wire, B. modulus of rigidity calculation, C. torque applied, D. angle of twist

    To determine the modulus of rigidity of a cylindrical wire by the torsion method, we use the torsion relation for a wire:



    where:
    - = torque applied
    - = radius of the wire
    - = length of the wire
    - = angle of twist
    - = modulus of rigidity

    The logical experimental order is:

    1. **Torque applied** — first, a twisting couple is applied to the wire.
    2. **Angle of twist** — due to the applied torque, the wire twists through some angle, which is measured.
    3. **Radius and length of wire** — the dimensions of the wire are needed as known quantities for the formula.
    4. **Modulus of rigidity calculation** — finally, substituting , , , and into the formula gives the modulus of rigidity.

    So the correct sequence is:
    - torque applied
    - angle of twist
    - radius and length of wire
    - modulus of rigidity calculation

    The marked answer already matches this correct order.
  5. Q5.
    For an isotropic material with Poisson's ratio , arrange the following quantities in increasing order: modulus of rigidity , Young's modulus , bulk modulus , and .
    • A.bulk modulus
    • B.Young's modulus
    • C.modulus of rigidity
    • D.
    Show answer and explanation

    Answer: A. bulk modulus , B. Young's modulus , C. modulus of rigidity , D.

    Using the relation with , we get . Also, using , we get , so . Thus the values are , , , and . Therefore, the actual increasing order is .
  6. Q6.
    Arrange the following materials in increasing order of Poisson's ratio under ordinary conditions: cork, steel, rubber, glass.
    • A.steel
    • B.rubber
    • C.glass
    • D.cork
    Show answer and explanation

    Answer: A. steel, B. rubber, C. glass, D. cork

    Poisson's ratio is very small for cork, about 0 for practical use, around 0.2 to 0.25 for glass, about 0.3 for steel, and nearly 0.5 for rubber. Therefore the increasing order is cork, glass, steel, rubber.
  7. Q7.
    A wire of the same material is stretched within the elastic limit. Arrange the following quantities in increasing order when stress increases: elastic potential energy density, strain, stress, and extension per unit length.
    • A.stress
    • B.elastic potential energy density
    • C.extension per unit length
    • D.strain
    Show answer and explanation

    Answer: A. stress, B. elastic potential energy density, C. extension per unit length, D. strain

    For a given material within the elastic limit, stress is proportional to strain by Hooke's law. Extension per unit length is also strain, so these two grow together. Elastic potential energy density is , so it depends on the product and increases more slowly at first but is conceptually a derived quadratic quantity. In standard ordering by dependence as stress rises, stress, strain, and extension per unit length are directly linked, while elastic potential energy density comes after them as the energy stored due to deformation. Hence the best increasing sequence is stress, strain, extension per unit length, elastic potential energy density.
  8. Q8.
    Arrange the following expressions in the correct logical sequence to derive elastic potential energy density of a stretched wire within elastic limit: Work done equals average force multiplied by extension. Force is proportional to extension. Energy per unit volume is obtained by dividing work by volume. .
    • A.
    • B.Energy per unit volume is obtained by dividing work by volume.
    • C.Force is proportional to extension.
    • D.Work done equals average force multiplied by extension.
    Show answer and explanation

    Answer: A. , B. Energy per unit volume is obtained by dividing work by volume., C. Force is proportional to extension., D. Work done equals average force multiplied by extension.

    To derive the elastic potential energy density of a stretched wire within the elastic limit, we proceed in the logical order of the physical ideas:

    1. **Force is proportional to extension.**
    Within the elastic limit, Hooke’s law applies, so the stretching force increases linearly with extension.

    2. **Work done equals average force multiplied by extension.**
    Since the force increases from to a final value , the average force during stretching is . Hence the work done is


    3. **Energy per unit volume is obtained by dividing work by volume.**
    If the wire has volume , then energy density is


    4. **.**
    Using

    we get


    So the given marked order is correct.
  9. Q9.
    For an isotropic solid under longitudinal stretching, arrange the following changes from most negative to most positive value: longitudinal strain, lateral strain, volumetric strain for a material with Poisson's ratio less than , and zero change.
    • A.volumetric strain
    • B.zero change
    • C.longitudinal strain
    • D.lateral strain
    Show answer and explanation

    Answer: A. volumetric strain, B. zero change, C. longitudinal strain, D. lateral strain

    During longitudinal stretching, the body contracts sideways, so lateral strain is negative. Zero change is greater than any negative value. For Poisson's ratio less than , volumetric strain in tension is positive because , and . Longitudinal strain is positive and typically larger than the volumetric strain factor. Thus the order from most negative to most positive is lateral strain, zero change, volumetric strain, longitudinal strain.
  10. Q10.
    Arrange the following cases in decreasing order of elastic potential energy density stored for the same tensile stress : material P with Young's modulus , material Q with , material R with , and material S with .
    • A.material R with
    • B.material P with Young's modulus
    • C.material S with
    • D.material Q with
    Show answer and explanation

    Answer: A. material R with , B. material P with Young's modulus , C. material S with , D. material Q with

    For the same stress, elastic potential energy density is . So energy density is inversely proportional to Young's modulus. The smaller the modulus, the greater the stored energy density for the same stress. Therefore decreasing order is P with , then Q with , then R with , then S with .

Practise all 279 Mechanics – Elasticity questions

Instant feedback, explanations, timed mock tests and progress tracking. Free on the web and Android.

Start practising free

More Physics chapters

All CEE Entrance subjects →